How to replace a clutch on a Citroën C4 Picasso

How to replace a clutch on a Citroën C4 Picasso

In this month’s Clutch Clinic, Schaeffler REPXPERT Alistair Mason is replacing the clutch assembly on a 2007 Citroën C4 Grand Picasso, fitted with a 1.8L 16-valve petrol engine that has covered more than 142,000 miles.


The customer had reported clutch slip and after the problem was confirmed, the vehicle was booked in. Following best practice, the parts were ordered ready for the job, the service information and technical bulletins were checked on REPXPERT prior to the repair, and the repair instructions and torque settings were also printed in advance.

With a scheduled time of 9.7 hours and only basic workshop equipment required, this repair is achievable below the scheduled time, so will make a profitable job for any independent workshop.

Advised workshop equipment

  • Vehicle lift (two-post is ideal)
  • Engine support
  • Transmission jack
  • Clutch alignment tool

Gearbox removal

With the vehicle on the ramp, open the bonnet and raise the vehicle to gain access to the underside. Remove the engine undertray and lower the vehicle to waist height, remove the N/S/F wheel and hub nut, followed by the N/S/F wheel arch liner. This now gives better access to the gearbox and makes visible the two battery tray retaining bolts (Fig 1), which must be removed to allow the later removal of the battery tray.

How to replace a clutch on a Citroën C4 Picasso

Lower the vehicle to gain access to the engine bay (Fig 2), remove the air box assembly, battery and tray, this now gives good access to the top of the gearbox, so the multiplugs for the reverse light switch and the crank speed sensor can be disconnected.

How to replace a clutch on a Citroën C4 Picasso

Unclip the battery to the engine wiring loom and disconnect the retaining bracket to give better access to the top bell-housing bolts, then remove the upper bell-housing bolts, disconnect the gear change cables and remove the crank sensor. Raise the vehicle to gain access to the underside and remove the N/S sub-frame leg (Fig 3). As the slave cylinder hydraulic pipe does not need to be slackened, remove the two clutch slave cylinder bolts and ease the slave cylinder away from the gearbox. Remove the gearbox drain plug and while the gearbox oil is draining, disconnect the N/S bottom ball joint and remove the N/S driveshaft.

How to replace a clutch on a Citroën C4 Picasso

Now, disconnect the gearbox pendulum mount (Fig 4), as this will allow the engine to move, and remove the gearchange cable bracket.

How to replace a clutch on a Citroën C4 Picasso

Tip – Whilst in this area, remove the O/S driveshaft seal housing, as this will eliminate the need to remove the O/S driveshaft (Fig 5). Remove the lower bellhousing bolts, leaving one easily accessible to support the gearbox.

Support the engine and remove the gearbox mounting and carefully lower the gearbox and engine assembly slightly to aid gearbox removal. Support the gearbox with a transmission jack, remove the final bellhousing bolt, and ease the gearbox away from the engine. Once clear, lower the gearbox and remove it from the vehicle.

Clutch replacement

Before removing the clutch, it is advisable to remove any excess clutch dust with some brake and clutch dust cleaner. Tip – It is good practice to note the position of the clutch components as they are removed as this may help with correct installation.

Remove the six clutch pressure plate bolts and then the clutch pressure plate and clutch plate assembly. This vehicle is fitted with a solid, single mass flywheel, the surface of which must be inspected for any heat cracks. Provided that it’s OK, remove any glaze from the flywheel surface with an Emory cloth, and clean with brake and clutch dust cleaner.

Attention now turns to the gearbox and clutch release system (Fig 6).

Remove the clutch release arm and release bearing, and inspect the release bearing guide tube for any wear (Fig 7), as well as the release arm and release arm pivot. In this instance, wear was evident, so the guide tube, arm and pivot were all replaced.

Check the bell-housing area for any oil leaks, and repair if required, then clean with brake and clutch dust cleaner. Fit the release bearing onto the guide tube and locate it into the release arm (Fig 8). Now, apply a light smear of high melting point grease to the splines on the gearbox input shaft and slide the clutch plate onto the input shaft. This will carry out two tasks: firstly, it ensures the clutch plate fits correctly; and second, it evenly distributes the grease. Then, remove the clutch plate and wipe off any excess.

Now, install the new clutch assembly onto the flywheel. Using a clutch alignment tool, and with the ‘Gearbox side’ on the clutch plate indicating its correct position (Fig 9), locate the clutch plate onto the flywheel, dowels. Install the bolts and tighten evenly and sequentially, and then torque to the manufacturer’s specification.

Gearbox installation

To aid installation, ensure the gearbox alignment dowels are located in the engine, and all cables and brackets are clear. Using the transmission jack, bring the gearbox close to the engine, and, if necessary, spend some time aligning the gearbox before easing it into position until it is aligned on the dowels and mated to the engine. Insert a couple of easily accessible bell-housing bolts and tighten to secure the gearbox to the engine.

Installation is in the reverse order of removal. Torque all bolts to the manufacturer’s specification, refill the gearbox with the correct specification and quantity of oil, and reset the required electrical consumers after the battery is reconnected. Finally, always carry out a road test to ensure you have completed a quality repair.


Information on Schaeffler products, fitting instructions, labour times and much more can be found on the REPXPERT workshop portal the REPXPERT app, or by calling the hotline on 0872 737 0037.

Related posts